The instructions below are valid for all OpenIAM v4.2.1.x deployments on CentOS 8 Stream and Red Hat Enterprise Linux (RHEL) 8.7+

This section describes how to install OpenIAM on either CentOS 8 Stream / RedHat Enterprise Linux (RHEL) 8.7+ using an RPM distribution.

OpenIAM provides an RPM distribution which includes all the dependencies except for the database and system tools to simplify the installation process. The completeness of the RPM file also enables deployments in locked down environments where there is no network.

You may download CentOS or RHEL from the following locations:

The installation instructions below require root level privileges on the host where OpenIAM will be deployed. The person or team installing OpenIAM must be familiar with the CentOS/RHEL operating system, databases and services.

The procedures described in this guide must be performed in the order that they have been presented below.

SSH into your VM

To ssh into your newly created VM, follow the steps below: a) First get the IP address of your VM. You can do this using:

ip addr

b) Next use a tool such Putty or the terminal window on Mac and SSH to this Linux host:

ssh [username]@[IP address of your VM]

Example: ssh root@172.16.101.128

Minimum System requirements

For non-production use, the Linux Host or VM must have the following minimum configuration:

Validate your environment

Login to your VM as root or a privileged user. To check the CPUs on your VM use: lscpu To the memory on your VM use: free -m

The result of each of these commands MUST align with the above minimum requirements. For sizing assistance for a production deployment, either open a support ticket or contact your OpenIAM point of contact.

Example of output from the above command is provided below.

[root@li1262-180 ~]# lscpu
Architecture:        x86_64
CPU op-mode(s):      32-bit, 64-bit
Byte Order:          Little Endian
CPU(s):              8
On-line CPU(s) list: 0-7
Thread(s) per core:  1
Core(s) per socket:  1
Socket(s):           8
NUMA node(s):        1
Vendor ID:           AuthenticAMD
BIOS Vendor ID:      QEMU
CPU family:          23
Model:               1
Model name:          AMD EPYC 7601 32-Core Processor
BIOS Model name:     pc-q35-3.1
Stepping:            2
CPU MHz:             2199.994
BogoMIPS:            4399.98
Hypervisor vendor:   KVM
Virtualization type: full
L1d cache:           64K
L1i cache:           64K
L2 cache:            512K
L3 cache:            16384K
NUMA node0 CPU(s):   0-7
Flags:               fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm rep_good nopl cpuid extd_apicid tsc_known_freq pni pclmulqdq ssse3 fma cx16 sse4_1 sse4_2 x2apic movbe popcnt tsc_deadline_timer aes xsave avx f16c rdrand hypervisor lahf_lm cmp_legacy cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw perfctr_core ssbd ibpb vmmcall fsgsbase tsc_adjust bmi1 avx2 smep bmi2 rdseed adx smap clflushopt sha_ni xsaveopt xsavec xgetbv1 xsaves virt_ssbd arat

[root@li1262-180 ~]# free -m
              total        used        free      shared  buff/cache   available
Mem:          31959         221       31473          16         264       31341
Swap:           511           0         511
[root@li1262-180 ~]# 

You may also run the following supporting commands to prepare the system for installation.

Command to check VM Operating System is as follows.

cat /etc/os-release

Example of output form the above command.

NAME="CentOS Stream"
VERSION="8"
ID="centos"
ID_LIKE="rhel fedora"
VERSION_ID="8"
PLATFORM_ID="platform:el8"
PRETTY_NAME="CentOS Stream 8"
ANSI_COLOR="0;31"
CPE_NAME="cpe:/o:centos:centos:8"
HOME_URL="https://centos.org/"
BUG_REPORT_URL="https://bugzilla.redhat.com/"
REDHAT_SUPPORT_PRODUCT="Red Hat Enterprise Linux 8"
REDHAT_SUPPORT_PRODUCT_VERSION="CentOS Stream"

Command to get system disk space is as follows.

df -H

Example of output form the above command.

Filesystem           Size  Used Avail Use% Mounted on
devtmpfs              17G     0   17G   0% /dev
tmpfs                 17G     0   17G   0% /dev/shm
tmpfs                 17G  8.9M   17G   1% /run
tmpfs                 17G     0   17G   0% /sys/fs/cgroup
/dev/mapper/cs-root   52G  2.4G   49G   5% /
/dev/mapper/cs-home   25G  209M   25G   1% /home
/dev/sda1            1.1G  295M  769M  28% /boot
tmpfs                3.4G     0  3.4G   0% /run/user/0

vi editor commands:

to edit -- type i
to escape -- hit esc
to save and quit -- type :wq

Prepare the host system for installation

The OpenIAM application requires a few configurations to be performed prior to installing the application. These steps are described below.

Install required packages

Before installing OpenIAM, please execute the commands below to install the required packages. If you have already logged in as “root”, you do not need to prefix them with “sudo”. If you have used another account, then you need to use “sudo”.

Tar utility. It is usually included in el7 CentOS, but not in el8.

Next steps

• Install with Internet Access
• Install without Internet Access